Oscilloscope Probes


High-performance 100 MHz Differential Amplifier

    Differential Amplifiers

DA1855A - 1 Ch, 100 MHz Differential Amplifier with Precision Voltage Source
DXC100A - ÷100 or ÷10 Selectable, 250 MHz Passive Differential Probe Pair
DXC200 - ÷1, 50 MHz, Passive Differential Probe Pair
DXC-5100 - 100:1 250 MHz 40 Mohm 2.75pf Differential Probe Pair;
DA101 - 10:1 1 MOhm Passive Attenuator
DA1855A-PR2 - 2 Ch, 100 MHz, Differential Amplifier with Precision Voltage Source
DA1855A-PR2-RM - 2 Ch, DA1855A with Rackmount (must be ordered at time of purchase, no retrofit)
DA1855A-RM - DA1855A with rackmount;
Differential amplifiers are intended to act as signal conditioning preamplifiers for oscilloscopes and network and spectrum analyzers, providing differential measurement capability to instruments having only a single-ended input. The "-PR2" version of each amplifier is a dual channel unit. The DXC series differential input cables are matched to the characteristics of the amplifier.
Features and Benefits
  • Full control from oscilloscope through ProBus interface
  • DC to 100 MHz bandwidth
  • Outstanding 100,000: 1 Common Mode Rejection Ratio (CMRR)
  • Gain of X1 or X10
  • Industry-leading overdrive recovery
  • Low noise
  • Selectable BW limiting
  • Two gain control modes when connected to a LeCroy oscilloscope
  • Built-in Precision Voltage Generator (PVG)
  • Comparator and true differential offset modes

The DA1855A is a stand-alone, high-performance 100 MHz differential amplifier. It is intended to act as a signal conditioning preamplifier for oscilloscopes, digitizers and spectrum analyzers, providing differential measurement capability to instruments having only a single-ended input. When used with a DA1855A, oscilloscopes can obtain Common Mode Rejection Ratio (CMRR) and overdrive recovery performance levels previously unobtainable.

Amplifier gain can be set to 1 or 10. A built-in input attenuator can be separately set to attenuate signals by a factor of 10, providing gains of 10, 1, or 0.1 and common mode dynamic range of ±15.5 V (÷1) or ±155 V (÷10). Optional probes increase the maximum input signal and common mode ranges in proportion to their attenuation ratio but do not exceed their maximum input voltage rating. Effective gain of the DA1855A, including probe attenuation, amplifier gain and attenuator settings, is automatically displayed.

The DA1855A has a bandwidth of 100 MHz, but any one of the three 3-pole bandwidth limit filters can be selected to reduce bandwidth to 20 MHz, 1 MHz or 100 kHz to limit noise above the frequency of interest.

The DA1855A output is carefully limited to ±500 mV, so that the oscilloscope is not overdriven by large inputs. This allows many oscilloscopes to directly measure the settling of D/A converters with 14-bit (60 ppm) precision, better than any other differential comparator.

The DA1855A features a built-in Precision Voltage Generator (PVG) that can be set to any voltage between ±15.5 V (±10 V in Differential Offset) with up to 100 µV resolution. The PVGs output can be selected as an input to the inverting (-) input of the amplifier for operation as a differential comparator or applied internally as a true differential offset voltage. The PVG is also available for external use through a rear panel connector.

The DA1855A operates from 90 to 250 VAC line without line switching. High-performance differential probes such as the DXC100 ÷10/÷100 high CMRR probes are recommended.

Overdrive Recovery

With a ÷100 probe, the DA1855A settles to within 100 mV referred to input, from a 400 V input signal within 100 ns. With attenuating probes, this allows the in circuit measurement of dynamic saturation in switch mode power converter switching devices.

Comparator Mode

The DA1855A becomes a differential comparator when the internal PVG output is selected as the amplifier's inverting (-) input. In this mode, the DA1855A can be used to very accurately measure relatively small signals that are riding on large AC or DC components. Due to the precision of the voltage generator, an oscilloscope, when used with the DA1855A, can make voltage measurements that are much more accurate than the oscilloscope is capable of by itself. The output of the PVG is available for external use via a rear panel connector.

True Differential Offset Mode

The DA1855A has built-in Precision Voltage Generator can be used to generate a true differential offset while still allowing both inputs to be used as differential inputs. The offset range can be as high as ±50,000 divisions and the generator has 5 1/2 digit resolution. This mode facilitates making measurements such as changes to a transistor's base to emitter voltage caused by variations in temperature and/or current. Used in this mode, the voltage generator can be set to a value that will zero out the static value of the junction's on voltage. The DA1855A's differential measurement capability will reject any dynamic signal common to both sides of the junction, and the oscilloscope is left to measure only the changes in the junction voltage.


Each time either gain setting button is pressed, the DA1855A automatically adjusts the amplifier's DC balance.

Main Specifications

Bandwidth >100 MHz

Electrical Characteristics

Risetime (typical) <3.5 ns

WaveSurfer 10 Oscilloscope

WaveSurfer 10
  Learn More
WaveSurfer 510 Oscilloscope

  Learn More
HDO4000A High Definition Oscilloscopes

  Learn More
WaveRunner 8000 Oscilloscopes

  Learn More
HDO6000A High Definition Oscilloscopes

  Learn More
HDO8000A High Definition Oscilloscopes

  Learn More
MDA800A Motor Drive Analyzers

  Learn More
WaveMaster / SDA / DDA 8 Zi-B Oscilloscopes

  Learn More