Products
Oscilloscope Probes

ADP300

1,400 V, 20 MHz High-Voltage Differential Probe


    High Voltage Differential Probes


HVD3102 - 1kV, 25 MHz High Voltage Differential Probe
HVD3102-NOACC - 1kV, 25 MHz High Voltage Differential Probe without tip Accessories
HVD3106 - 1kV, 120 MHz High Voltage Differential Probe
HVD3106-NOACC - 1kV, 120 MHz High Voltage Differential Probe without tip Accessories
HVD3106-6M - 1kV, 80 MHz High Voltage Differential Probe with 6m cable
HVD3206 - 2kV, 120 MHz High Voltage Differential Probe
HVD3206-6M - 2kV, 80 MHz High Voltage Differential Probe with 6m cable
HVD3605 - 6kV, 100 MHz High Voltage Differential Probe
AP031 - 700 V, 25 MHz High-Voltage Differential Probe (÷10, ÷100)
ADP300 - 1kV, 20 MHz High-Voltage Differential Probe
ADP305 - 1kV, 100 MHz High-Voltage Differential Probe

Teledyne LeCroy high voltage differential probes provide high CMRR over a broad frequency range to simplify the measurement challenges found in noisy, high common-mode power electronics environments.The probe’s design is easy-to-use and enables safe, precise high voltage floating measurements.

The HVD3000 series of high voltage differential probes cover the fullest range of applications, from 120/240 V switch-mode power supplies through 600 V class and 5 kV class electricalapparatus. The table below provides a list of recommended probe models based on specific device under test applications.

Device Under TestRecommended ModelSafety ClassBandwidthCable LengthTip Accessories Included
120 V/240 V Half-Bridge Circuit TopologiesHVD31021 kV25 MHz2 mYes
HVD3102-NOACC1 kV25 MHz2 mNo
HVD31061 kV120 MHz2 mYes
HVD3106-NOACC1 kV120 MHz2 mNo
380 V - 600 V Class Electrical ApparatusHVD31061 kV120 MHz2 mYes
HVD3106-NOACC1 kV120 MHz2 mNo
HVD3106-6M1 kV80 MHz6 mYes
Solar PV InverterHVD31061 kV120 MHz2 mYes
HVD32062 kV120 MHz2 mYes
HVD3206-6M2 kV80 MHz6 mYes
5 kV Electrical ApparatusHVD36058.485 kV100 MHz6 mYes
Leading Specifications
  • 20 MHz and 100 MHz bandwidth
  • 1,000 VRMS common mode voltage
  • 1,400 Vpeak differential voltage
  • EN61010 Cat III
  • 80dB CMRR at 50/60 Hz
  • ProBus® system
  • Full remote control
  • Compatible with LC Series, LT Series, WS 400 Series, WS Xs Series, WR6000(A) Series, WR Xi Series, WP 900 Series, WP7000(A) Series

ADP30X high-voltage active differential probes are safe, easy-to-use probes ideally suited for measuring power electronics. The ADP300 is good for troubleshooting low-frequency power devices and other circuits where the reference potential is elevated from ground or the location of ground is unknown. The ADP305 is designed for measuring the high-speed floating voltages found in today''s high-speed power electronics.

Easy-to-Use
With the ProBus® interface, the ADP30X becomes an integral part of the oscilloscope.

The attenuation, offset, and bandwidth limit are all controlled from the oscilloscope front panel or by using the remote control commands. This means the complete measurement setup can be saved and recalled by the oscilloscope, and all measurement values will be correct. The scope provides power to the probe, so there is no need to worry about a separate power supply or changing batteries.

Autozero
The ADP30X offset can be easily set to zero by pushing a button in the oscilloscope''s coupling menu, even when connected to live circuits. This makes it easy to get accurate measurements.

Meets EN61010 Category III Requirements
Safety is the top priority when you work around high-voltage signals. The ADP300 and ADP305 are both designed to the standards required for Installation Category III. This means in addition to being used on appliances and portable equipment (Cat II), they can be used in fixed-installation environments.

Main Specifications

Attenuation ÷100 or ÷1000, automatically selected by scope
 

WaveSurfer 10 Oscilloscope

WaveSurfer 10
  Learn More
MDA800 Motor Drive Analyzers

MDA800 Motor Drive Analyzers
  Learn More
WaveMaster / SDA / DDA 8 Zi-B Oscilloscopes


  Learn More