Products
Oscilloscope Probes

ZS2500

2.5 GHz, 0.9 pF, 1 MOhm Active Voltage Probe


    Active Voltage Probes


ZS4000 - 4.0 GHz, 0.6 pF, 1 MOhm Active Voltage Probe
ZS2500 - 2.5 GHz, 0.9 pF, 1 MOhm Active Voltage Probe
ZS1000 - 1 GHz, 0.9 pF, 1 MOhm Active Voltage Probe
ZS1500 - 1.5 GHz, 0.9 pF, 1 MOhm Active Voltage Probe
ZS2500-QUADPAK - Set of 4 ZS2500, 2.5 GHz High Impedance Active Probes
ZS1000-QUADPAK - Set of 4 ZS1000, 1 GHz High Impedance Active Probes
ZS1500-QUADPAK - Set of 4 ZS1500, 1.5 GHz High Impedance Active Probes
ZS Series High Impedance Active Probes

The ZS Series probes provide high impedance and an extensive set of probe tips and ground accessories to handle a wide range of probing scenarios. The high 1 MΩ input resistance and low 0.9 pF input capacitance means this probe is ideal for all frequencies. The ZS Series probes provide full system bandwidth with all Teledyne LeCroy oscilloscopes with bandwidths of 4 GHz and lower.

ModelBandwidthInput RInput CDynamic Range OffsetRangeInterface
ZS10001 GHz1 MΩ0.9 pF± 8 VNAProBus
ZS15001.5 GHz1 MΩ0.9 pF± 8 V± 12 VProBus
ZS25002.5 GHz1 MΩ0.9 pF± 8 V± 12 VProBus
ZS40004 GHz1 MΩ0.6 pF± 8 V± 12 VProBus
Key Features
  • Easy to use, integrated with oscilloscope
  • High Signal Fidelity to 2.5 GHz Bandwidth
  • Low Circuit Loading – High Input impedance and low capacitance
  • ± 8 V input dynamic range
  • 1 MΩ input resistance
  • 0.9 pF input capacitance
  • ± 12 V offset range
  • ProBus interface
  • Wide variety of tips and leads


High Impedance Reduces Circuit Loading across Full Oscilloscope Bandwidth

Engineers must commonly probe high frequency signals with high signal fidelity. Typical passive probes with high input R and C provide good response at lower frequencies, but inappropriately load the circuit, and distort signals, at higher frequencies. The ZS Series features both high input R (1 MΩ) and low input C (0.9 pF) to reduce circuit Loading across the entire probe/oscilloscope bandwidth. The ZS2500 is ideal for 2.5 GHz and lower oscilloscopes.

A Variety of Probe Tips for Varied Tasks

The small form factor and extensive range of standard and optional tip accessories for the ZS Series of probes ensures that this probe can meet any difficult probing challenge. Various flexible leads and clips, such as right-angle leads, Y-adapters, and pico hooks, are also available for probing test points that are spaced farther apart.

Innovative Grounding Provide the Highest Signal Fidelity

Keeping the ground loop short is critical to eliminating the effect of high inductance on the signal. The ZS Series of probes provides several grounding capabilities to offer the highest signal fidelity by eliminating the effect of that loop on the signal.

Electrical Characteristics

Bandwidth (Probe Only) 2.5 GHz
Input Resistance 1 MΩ
Input Capacitance 0.9 pF
Offset Range (Probe) ± 12 V
Input Dynamic Range ± 8 V
Attenuation 10:1
Coupling 50 Ω, GND
Non-Destruct Voltage 20 V
 

Environmental and Safety

Operating Temperature 0 °C to 50 °C
(32 °F to 122 °F)
Humidity 80% Max up to 31 °C
45 % Max at 50 °C
Storage Temperature -40 °C to 71 °C
(-40 °F to 160 °F)
Max Altitude 2000 m
(6562 ft)
 

Physical Dimensions

Probe Head Dimensions (L x W x H) 61 mm x 7.3 mm x 13.1 mm
(2.4 in x .29 in x .52 in)
Input Sockets .635 mm (.025 in) square pin
.91 m (.036) round pin
Cable Length 1.3 m
(4.25 ft)
Weight 100 g
(3.5 oz)
 

General Characteristics

Interface ProBus
Compatibility All ProBus Oscilloscopes