Products
Oscilloscope Probes

CA10

Programmable ProBus Current Adapter


    Current Probes


CP030 - 30A, 50 MHz Current Probe - AC/DC, 30 A rms, 50 A Peak Pulse, 1.5 meter cable
CP030A - 30A, 50 MHz High Sensitivity Current Probe - AC/DC, 30 A rms, 50 A Peak Pulse, 1.5 meter cable
CP031 - 30A, 100 MHz Current Probe - AC/DC, 30 A rms, 50 A Peak Pulse, 1.5 meter cable
CP031A - 30A, 100 MHz High Sensitivity Current Probe - AC/DC, 30 A rms, 50 A Peak Pulse, 1.5 meter cable
CP150 - 150 A, 10 MHz Current Probe - AC/DC, 150 A rms, 500 A Peak Pulse, 2 meter cable
CP500 - 500 A, 2 MHz Current Probe - AC/DC, 500 A rms, 700 A Peak Pulse, 6 meter cable
CA10 - Programmable Current Sensor to ProBus Adapter for use with third party current sensors
CA10-QUADPAK - Set of 4 CA10 Programmable Current Sensor to ProBus Adapters for third-party current sensors
DCS015 - Deskew Calibration Source for CP031,CP031A, CP030, CP030A and AP015
Current Probes

Teledyne LeCroy current probes are available in a variety of models for a wide range of applications. The full range of Teledyne LeCroy current probes includes models with bandwidths up to 100 MHz, peak currents up to 700 A and sensitivities to 1 mA/div. Teledyne LeCroy current probes are often used in applications such as the design and test of switching power supplies, motor drives, electric vehicles, and uninterruptible power supplies.

  • CP030 - 30A, 50MHz Current Probe
  • CP030A - 30A, 50MHz High Sensitivity Current Probe
  • CP031 - 30A, 100MHz Current Probe
  • CP031A - 30A, 100MHz High Sensitivity Current Probe
  • CP150 - 150 A, 10 MHz Current Probe - AC/DC, 150 A rms, 500 A Peak Pulse
  • CP500 - 500 A, 2 MHz Current Probe - AC/DC, 500 A rms, 700 A Peak Pulse
  • DCS015 - Deskew Calibration Source for CP031,CP031A, CP030, CP030A and AP015

 

Current Sensor Adapter

The CA10 is a programmable and customizable interface device that seamlessly incorporates third party current transducers/transformers with Teledyne LeCroy oscilloscopes or motor drive analyzers. The easy to use interface provides the ability for the CA10 to be programmed to contain the specifications of the current sensor allowing it to automatically correct for the gain or attenuation and display results in Ampere units. This allows the third party device to be recognized and operate as if it were a Teledyne LeCroy probe.

  • CA10 - Programmable ProBus Current Sensor Adapter for use with third party current sensors
  • CA10-QUADPAK - Set of 4 CA10, Programmable ProBus Current Sensor Adapter for use with third party current sensors
Key Features
  • Provides ability for third party current sensor to operate like a Teledyne LeCroy probe
  • Programmable EEPROM for saving third party current sensor parameters
  • Allows for addition of shunt resistor and RLC filter components
  • ProBus Active interface with automatic scaling in A/div
  • Easy to use, saves time and possible errors

The CA10 is a programmable and customizable interface device that seamlessly incorporates third party current transducers/transformers with Teledyne LeCroy oscilloscopes or motor drive analyzers. It allows the third party device to be recognized and operate as if it were a Teledyne LeCroy probe.

Measurement Flexibility

Examples of devices that can be used with the CA10 include Pearson Current Transformers, Danisense/LEM Current Transducers, PEM-UK Rogowksi Coils, or any conventional turns-ratio current transformers. Once the CA10 is programmed, the third party transducer/transformer will be recognized and operate like a Teledyne LeCroy probe.

Power of Customization

The CA10 provides the ability to easily install physical hardware components such as shunt resistors and bandwidth filter components based on the requirements of the device being used.

The CA10 also has programmable bandwidth limit filters of full BW, 200 MHz, or 20 MHz.

Easy to Use

The programmable interface is intuitive and easy to use. Once the CA10 is configured, it will recognize the third party device with the correct scaling factors on any compatible Teledyne LeCroy oscilloscope or motor drive analyzer. This saves time and possible errors involved in manually entering scaling factors each time the device is connected.

WaveRunner 8000 Oscilloscopes


  Learn More
MDA800 Motor Drive Analyzers

MDA800 Motor Drive Analyzers
  Learn More
WaveMaster / SDA / DDA 8 Zi-B Oscilloscopes


  Learn More