Oscilloscope Probes


Power/Voltage Rail Probe. 4 GHz bandwidth, 1.2x attenuation, +/-30V offset, +/-800mV

    Active Voltage Rail Probe

RP4030 - Power/Voltage Rail Probe. 4 GHz bandwidth, 1.2x attenuation, +/-30V offset, +/-800mV Includes a complete set of solder-in leads, coaxial cables, and PCB mounts.
RP4000-BROWSER - RP4030 350 MHz Browser Tip accessory. Includes 0 Ohm (1x), 450 Ohm (10x) and 950 Ohm (20x) tips.
RP4000-MCX-LEAD-SI - Qty. 3 MCX 4 GHz solder-in lead accessories (additional to those supplied with RP4030), 18cm long
RP4000-MCX-PCBMOUNT - Qty. 10 MCX 6mm x 6mm PCB mounts (additional to those supplied with RP4030)
RP4030 Active Voltage Rail Probe

The Teledyne LeCroy RP4030 Power Rail Probe meets the specific requirements of those who need to acquire a low-voltage DC signal as part of a:

  • Comprehensive power integrity, digital power management IC (PMIC), voltage regulator module (VMR), point-of-load (POL) switching regulator, or low-dropout regulator testing
  • Complete embedded power management system that includes PMICs, VRMs, POLs, and LDOs

The RP4030 will faithfully acquire a low-impedance, low-voltage DC power/voltage rail signal without unduly loading the device under test (DUT), while providing high offset to allow DC power/voltage rail signal display on an oscilloscope with high gain.

Large Offset Range

+/-30V offset permits the DC signal to be displayed in the vertical center of the oscilloscope grid with a high-sensitivity gain setting (maximum +/-800mV dynamic range).

Low Attenuation and Noise

The probe attenuation is a nominal 1.2x coupled to the oscilloscope at DC 50 Ω. This keeps additive noise to a minimum, and makes it exceptionally useful with HDO oscilloscopes for lowest noise at highest sensitivity gain settings.

High DC Input Impedance

50 kΩ input impedance at DC effectively eliminates probe loading on the DC power/voltage rail and provides for more accurate measurements and signal fidelity.

4 GHz of Bandwidth

Provides maximum bandwidth for probing near the CPU, and the perfect match with the 4 GHz,12 bit WavePro 404HD when making power integrity measurements.

Wide Assortment of Tips and Leads

The RP4030 is supplied standard with solder-in and coaxial cables with MCX and U.FL PCB receptacle mounts. A browser tip is optionally available. Additional receptacles or leads may be purchased as accessories and left connected in circuit for easy connection of different signals during different tests or validation stages.

Optional Browser Tip

A 350 MHz browser tip is available as an accessory. This browser tip is a conventional transmission line probe with a "pass-through"" 0Ω resistor to achieve 50Ω tip impedance and 1x attenuation. When used with the RP4030, high DC input impedance is also achieved. The browser tip accessory is also provided with 450Ω and 950Ω resistors for use as a conventional 10x or 20x transmission line probe.


Electrical Characteristics

Offset Range +/-30V
Noise ~5% additive to oscilloscope noise (when used with HD4096 oscilloscope)
Rise Time (10–90%) 110 ps (typical, MCX receptacle or solder-in lead)
Bandwidth 4 GHz (guaranteed, MCX receptacle)
4 GHz (typical, solder-in lead)
3 GHz (typical, U.FL cable + receptacle)
350 MHz (typical, browser)
Input Capacitance 0.1 μF (in series with 50 Ω)
Attenuation 1.2x
Input Dynamic Range +/-800 mV
Non-Destruct Voltage +/-50V
DC Input Resistance (nominal) 50 kΩ

WaveSurfer 3000z Oscilloscopes

WaveSurfer 3000z Oscilloscopes
   Learn More
WaveSurfer 4000HD High Definition Oscilloscopes

WaveSurfer HD
   Learn More
HDO4000A High Definition Oscilloscopes

   Learn More
HDO6000B High Definition Oscilloscopes

   Learn More
WaveRunner 8000HD 8 Channel High Definition Oscilloscopes

WaveRunner 8000HD

   Learn More
MDA 8000HD Motor Drive Analyzers

MDA 8000HD Motor Drive Analyzers

   Learn More
WavePro HD Oscilloscopes

WavePro HD Oscilloscopes
   Learn More
WaveMaster / SDA / DDA 8 Zi-B Oscilloscopes

   Learn More
LabMaster 10 Zi-A Oscilloscopes

   Learn More